top of page
Peregrine-X-Logo-wo

Peregrine X Client Questionnaire

Thank you for taking the time to complete this short questionnaire.  Please complete only questions that are relevant to you. Your responses will enable Peregrine X to focus specifically on your current challenges and provide tailored solutions. All information provided is kept strictly confidential.

PACE24 Rapid Oil & Fluid Analysis

Our PACE24 Rapid Oil & Fluid Analysis can help you resolve key operational challenges, including:

  Production Allocation / Reservoir Monitoring
  Chemical Optimisation (Existing Products)
  Chemical Trials (New Products)
  Wax Cutting

  Asphaltene Detection
  Injection Water Tracking to Calibrate Reservoir Models
  Processing and Clean-Up of Contaminated Areas
  Corrosion Prevention
  Monitoring of Transmission, Lubrication, Power, or Hydraulic Fluids

1. Production Allocation

Do you want to:

How we can help:

PACE24 can analyse collected samples to determine the percentage contribution from component reservoirs – enabling production allocation from reservoirs where conventional metering cannot differentiate.

2. Reservoir Monitoring

Do you want to:

How we can help:

PACE24 can analyse collected samples to determine the percentage contribution from component reservoirs.  You can then fine tune reservoir models by analysing produced fluid.

3. Chemical Optimisation (existing products)

Are you looking to:

How we can help:

PACE24 analyses downstream of injection points, detecting the presence of injected chemicals. As the dosage is reduced, we take additional samples and analyse within hours. We can help you find the optimum dosage, mix combination and type of chemicals, optimising expenditure when budgets are tight.

4. Chemical Trials (new products)

Are you:

How we can help:

PACE24 rapidly analyses different selected chemicals during field trials and determines the optimum dosage (as per chemical optimisation process).  Continued monitoring of the system can be used to ensure the optimum volume of chemicals are always added.

5. Wax Cutting

Are you:

(Note: this is equally applicable to scale problems).

How we can help:

PACE24 analyses surface samples after wax cutting. Over time, this will indicate drop-out upstream of the sampling point and build-up within tubing requiring cutting.  For multiple wells this enables operators to prioritise frequency of cutting – maximising crew efficiency and reducing well shut-in.

6. Injection water tracking – calibration of reservoir models, optimised water injection

Are you:
Could your injection volumes be:

How we can help:

As the number of injection wells are increased, it is often difficult to assess their impact on each other and the reservoir.

 

By adding different tracers at each injection well and analysing produced water samples, PACE24 can identify the presence of any of the added tracers and enable an operator to establish the flow of injected water throughout the reservoir and calibrate complex reservoir models.  The failure to detect any of the tracers would suggest that injected water tagged with that tracer is not contributing to the water injection plan.

7. Processing and clean-up of contaminated areas

Are you responsible for land which has been contaminated? If so, what is the:

Are you:

Due to tightening environmental regulations and ESG compliance, there is an increasing requirement to ensure that inactive or abandoned locations (well sites, gathering stations, storage areas) are not contaminated or have been sufficiently cleaned-up to remove known contamination.

How we can help:

PACE24 tests for known contaminants. Analysis within a few hours with a field lab or less than 24 hours in a remote laboratory. 

By comparison, rival techniques take 3 days + and are less accurate.

8. Corrosion Prevention

What is:

Failure of equipment due to corrosion can be costly. As with the chemical optimisation process, corrosion inhibitors would be added with downstream samples being tested for both corrosion inhibitor and corrosion products.

How we can help:

PACE24 analyses downstream of injection points, detecting the presence of injected chemicals and whether they are active or spent. Ie. has the corrosion issue been addressed and are more/less chemicals needed to suppress detected corrosion products.

9. Monitoring of transmission, lubrication, power or hydraulic fluids

Are you using heavy/rotating equipment which requires transmission, lubrication or hydraulic fluids?   Most companies replace fluids on a routine basis to avoid equipment failure that would result in considerable downtime and loss of revenue? Would you want a monitoring service to quantify any equipment degradation or oil contamination?

If this is a service of interest, please provide the following information to enable us to discuss your challenge(s) with you;

How we can help:

By monitoring and optimising the use of transmission, lubrication or hydraulic fluids. PACE24’s rapid analysis samples fluids and detects materials representative of wear (e.g. copper from bearings) or erosion (sand in equipment).

By replacing fluids only when necessary, significant cost savings can be made.

Would you like to discuss how PACE24 Rapid Oil Analysis can help your operations?

Contact information

We appreciate your time and look forward to assisting you.

bottom of page